Connected with ClubSport Wheel Base V2.5 PC, the steering is significantly off center.

実 大谷実 大谷 Member
in Wheel Bases (and Racing Wheels)

At first it worked normally, but suddenly something went wrong.

The problem is that when the ClubSport Wheel Base V2.5 is connected to the PC, the car cannot go straight unless the steering wheel is turned 45 degrees to the left. Please help me figure out the solution.

Comments

  • Remco Van DijkRemco Van Dijk Member

    Did you update the firmware and not reset the wheel center? See the CSW v2.5 Manual on how to reset the wheel center.

    https://fanatec.com/media/pdf/39/93/ed/CSW-V2-5_Manual-EN_01.pdf

  • 実 大谷実 大谷 Member

    Even though my CSW2.5 is centered on the steering as shown in the image below, the value is -205 and I can not go straight.

    i did Calibration.

    i still have a probrem.

    Please help someone how to fix it.

    IMG-6327.jpg


  • 実 大谷実 大谷 Member

    This is my information！

    Something wrong？

    windows10


    ClubSport Wheel Base V2.5

    ClubSport Pedals V3


    PCdriver：347

    Wheel Base Firmware:664

    Wheel Base Motor Fiemware:22

    Best Regards

  • Lee RobertsLee Roberts Member
    edited February 2020

    Reset your wheel centre as Remco Van Dijk linked before follow those directions and it will be fine


  • 実 大谷実 大谷 Member
    edited February 2020

    I tried many times as instructed, but the problem did not improve.

    s there any other way? 　Is The driver not suitable？


    Best Regards

  • Remco Van DijkRemco Van Dijk Member
    edited February 2020
    https://forum.fanatec.com/discussion/comment/38894#Comment_38894

    You'll have to describe in more detail how re-calibrating the wheel center does not improve the problem. If you put the physical steering wheel in the centered position and then reset the wheel center (either by the button combination as shown in the manual or by clicking the button in the driver), the position must be set to zero again.

    It is possible that the wheel loses the center position again when using it, but then it's not the same angle all the time which is what you seem to be describing. Please describe exactly what the problem is, and what you see when you reset the wheel center position as described above.

  • 実 大谷実 大谷 Member

    Hello

    I send a few photos and videos.

    The video has been uploaded to youtube exclusively.


    I tried various drivers and installed it, but it didn't change. The V3 pedal does not respond. The current driver is back to V328 downloaded from HP.


    The steering is still at -205.

    When you turn the steering wheel to the right, it will move quickly at the end.

    Is it a steering failure?　Best Regars

    IMG-6373.jpg
    IMG-6372.jpg
    IMG-6371.jpg
    IMG-6370.jpg


    https://youtu.be/aa5_34ZDzko

    https://youtu.be/x6n8Ojd-8Nc




















    cleardot.gif


  • Remco Van DijkRemco Van Dijk Member
    edited February 2020

    I see you pushing the correct buttons to do the wheel center calibration, however you should always do it with the Fanatec Wheel Properties screen open so you can verify that the center was indeed set to zero. The center position calibration is a bit difficult because if you don't press the buttons exactly at the same time, nothing will happen and the center is still not set to zero. Usually it takes me two or three attempts before I get it right and the center position is indeed set to zero.

    So please do try the procedure again with the Fanatec Wheel Properties window open so you can really see the center position being calibrated (set to zero) properly.

Sign In or Register to comment.